Retarder Assembly LZ Type SJL00003 Handle Switch

The TR series includes 4 models. Compact structure, light weight, small size, easy to disassemble and assemble; The rotor adopts a cylindrical structure, a fully machined surface, and a beautiful appearance; Low power consumption, no need to replace the original car generator; The braking torque is large, 100-300NM larger than other similar structure eddy current retarders, and the maximum braking torque can be reached at low speed (vehicle speed is about 15km/h); Radial distribution, so that the rotor gap is not affected by the bearing movement, making the eddy current retarder run more reliable and more widely matched; The axial length is small, the weight of the rotor is light (about 20kg), and the impact on the original vehicle’s transmission system is small; The installation space required is small, especially suitable for medium-sized vehicles with short rear suspension and unable to shorten the drive shaft; Adopt digital and intelligent control system, safer work and more reliable operation.

The control handle switch is installed at the lower right of the steering wheel, it is a multi-functional combination switch, the retarder can be controlled by pulling the retarder handle switch. Installed in the cockpit. The driver realizes the braking of the vehicle by selecting the appropriate gear. Typically mounted on the dashboard or under the steering wheel, it will provide one neutral gear and four to six control gears.
The manual switch is divided into 5 gears, 0 means the retarder is closed, 1 means the retarder constant speed gear, 2 means 1/4 of the maximum retarding torque, 3 means 1/2 of the maximum retarding torque , 4th gear represents 3/4 of the maximum retarding torque, and 5th gear represents the maximum retarding torque.

The contact assembly of the static and dynamic contacts of the relay includes a static contact piece, a moving contact piece, a moving reed piece, a push card, two static contacts and two moving contacts. The dynamic and static contact structure improves the current breaking performance and prolongs the electrical life.
Relay is a kind of electric control device, is when the change of the input quantity to meet the specified requirements, in the electrical output circuit to make the controlled quantity of a predetermined step change of an electrical appliance. Relay has control system and controlled system, usually used in the automatic control circuit, in the circuit plays the role of automatic regulation, safety protection, conversion circuit and so on.

The diameter of this TERCA Two-in-one retarder flange for end face is 162mm, the thickness is 25mm, the flange screws are M14, and the drive shaft screws are M12.
Whether you operate a fleet of commercial trucks, heavy machinery, or specialized vehicles, our retarder flanges are engineered to optimize your braking system’s efficiency. Experience the difference in braking performance and safety with our high-quality retarder flanges.

B5-15 retarder stator assembly frame is evenly equipped with 8 stator magnetic cores, and the stator magnetic cores are wound with coils.
The retarder stator coil assembly has several groups of internal coils, which are the main working parts of retarder. It is connected with the chassis of the vehicle through a fixed bracket. The stator is the stationary part of a motor. The stator consists of three parts: stator core, stator winding and frame.
The action of the stator is to produce an alternating current and the action of the rotor is to create a rotating magnetic field.

Experience the pinnacle of wiring technology with the Retarder B Series Four Pillars Wiring Board. Designed to deliver unmatched connectivity and performance, this groundbreaking wiring board is set to revolutionize electrical systems.
With its advanced design and cutting-edge features, the Retarder B Series Wiring Board seamlessly integrates with four pillars retarders, enabling smooth and efficient power transmission. This wiring board is engineered for optimal performance, minimizing energy loss and maximizing the overall efficiency of your systems.

TB series eddy current retarder contains 9 models in total. Suitable for installation in various gearboxes or rear axles; Compact structure and light weight; High electric power, low power consumption; The turntable made of special materials has small thermal deformation and low thermal decay of braking torque; Large braking torque, wide torque range, suitable for all kinds of large and medium-sized passenger cars, trucks and special vehicles; Adopt digital and intelligent controller, safer to use and more reliable to work; The blade has undergone technical reforms, which not only maintains a better heat dissipation capacity, but also greatly reduces the drag coefficient.

This TERCA flange is used to match the 153 rear axle. The black one has a diameter of 166mm and a thickness of 34mm. The white one is 175mm in diameter and 28mm thick.
Crafted from high-quality materials, our retarder flanges are built to withstand extreme temperatures, heavy loads, and continuous usage. Count on their durability and reliability to deliver consistent performance over an extended period.

The stator has several groups of internal coils, which are the main working parts of retarder. It is connected with the chassis of the vehicle through a fixed bracket. The stator is the stationary part of a motor. The stator consists of three parts: stator core, stator winding and frame.
The main function of the stator is to generate a rotating magnetic field, while the main function of the rotor is to be wire-cut in the rotating magnetic field to generate a current.

Fast-selling modity FV61-30 bus brake retarder stator assembly suitable for TELMA eddy current retarder. The stator has several groups of internal coils, which are the main working parts of retarder. It is connected with the chassis of the vehicle through a fixed bracket. The stator is the stationary part of a motor. The stator consists of three parts: stator core, stator winding and frame.
The action of the stator is to produce an alternating current and the action of the rotor is to create a rotating magnetic field.

There are seven models in the DHB series eddy current retarder. Suitable for long-distance and tourist buses with rear gearboxes. The stator is made of aerospace die-cast aluminum alloy, which is anti-magnetization, high strength, light weight and good size stability. The rotor is made of special high-temperature resistant alloy casting, with small deformation and no remanence; the heat dissipation channel adopts a multi-layer structure, which has large ventilation and small thermal decay.

The handle switch is divided into 5 gears, 0 means the retarder is closed, 1 means the retarder constant speed gear, 2 means 1/4 of the maximum retarding torque, 3 means 1/2 of the maximum retarding torque, The 4th gear represents 3/4 of the maximum retarding torque, and the 5th gear represents the maximum retarding torque.
When the car is ignited, the retarder is in a standby state. When the car needs to be slowed down, the purpose of slowing down can be achieved by turning the handle of the manual switch to the required gear step by step. If you want to turn off the slowing down function, just use the handle Turn the control switch handle back to 0 gear.

The brand name of F191 and 71-95 brake retarder stator assembly is TELMA. The stator has several groups of internal coils, which are the main working parts of retarder. It is connected with the chassis of the vehicle through a fixed bracket. The stator is the stationary part of a motor. The stator consists of three parts: stator core, stator winding and frame. The action of the stator is to produce an alternating current and the action of the rotor is to create a rotating magnetic field.

The eddy current retarder B series five pillars 0.2KGS wiring board is a critical component within the eddy current retarder system, specifically designed to facilitate the electrical connections and functionality of the system. This wiring board plays a crucial role in ensuring proper communication and power distribution between various components of the eddy current retarder.
Wiring board is a type of socket. It is a porous socket formed by placing multiple sockets together. Simply speaking, a wiring board socket is a porous socket with a power cord and plug and can be moved. It is a common name of a power converter. A wiring board socket can be used for multiple purposes, saving space, saving lines, simple and practical.

The diameter of this TB24 flange is 182mm, the thickness is 45mm, the flange screw is M16, and the drive shaft screw is M16.
We understand that different vehicles and applications have unique requirements. That’s why we offer customizable options, allowing you to select the retarder flange that best suits your specific needs. From size and shape to material composition, we can tailor our product to match your exact specifications.

The stator has several groups of internal coils, which are the main working parts of retarder. It is connected with the chassis of the vehicle through a fixed bracket. The stator is the stationary part of a motor. The stator consists of three parts: stator core, stator winding and frame.
The stator frame is evenly equipped with 8 stator core, the stator core is wound with a coil, the stator frame is evenly opened with 8 core holes, the stator core is inserted in the hole and fixed on the stator frame, the two side segments of the extended core hole of the stator core are symmetrically distributed on both sides of the stator frame; Both ends of each stator core are fixedly connected with magnetic conductive plates.
The action of the stator is to produce an alternating current and the action of the rotor is to create a rotating magnetic field.

The stator bracket is used to support the stator. During the operation of the retarder, the bracket of the stator bracket can prevent the stator from shaking.
Eddy current retarder is generally composed of stator, rotor and fixed bracket. The diameter and weight of the single stator bracket are much smaller than that of the assembled stator.The stator includes a stator bracket and an iron core and coil, which are secured by the bracket. The stator bracket is an indispensable part of retarder.

It is an electronic control device, which has a control system (also known as an input circuit) and a controlled system (also known as an output circuit), and is usually used in an automatic control circuit. It actually uses a smaller current to control a larger current A kind of “automatic switch”.
SZZ52006 two gears relay box is a kind of electric control device, is when the change of the input quantity to meet the specified requirements, in the electrical output circuit to make the controlled quantity of a predetermined step change of an electrical appliance. Relay has control system and controlled system, usually used in the automatic control circuit, in the circuit plays the role of automatic regulation, safety protection, conversion circuit and so on.

The diameter of this TERCA flange is 100mm, the thickness is 25mm, there are four holes, and the drive shaft screw is M16.
Our retarder flanges are designed for easy installation, minimizing downtime and maximizing productivity. With clear instructions and compatibility with standard braking systems, integrating our flanges into your existing setup is a seamless process.

The eddy current retarder relay block is a critical component within the realm of automotive engineering, specifically in vehicles equipped with eddy current retarder systems. This relay block serves as the central control unit, facilitating the efficient operation and coordination of the various components involved in the eddy current retarder system.
This relay block effectively controls the engagement and disengagement of the eddy current retarder, allowing seamless integration with the vehicle’s overall braking and acceleration systems. It ensures optimal performance, smooth operation, and enhanced safety by monitoring parameters such as vehicle speed, engine RPM, and temperature.

DHB series retarder stator is made of aerospace die-cast aluminum alloy, which is anti-magnetization, high strength, light weight and good size stability.
The stator has several groups of internal coils, which are the main working parts of retarder. It is connected with the chassis of the vehicle through a fixed bracket. The stator is the stationary part of a motor. The stator consists of three parts: stator core, stator winding and frame.
The main function of the stator is to generate a rotating magnetic field, while the main function of the rotor is to be wire-cut in the rotating magnetic field to generate a current.

The stator assembly is a kind of retarder parts. DX1300 TELMA retarder parts stator assembly is suitable for Telma DX series eddy current retarder.
The stator assembly has several groups of internal coils, which are the main working parts of retarder. It is connected with the chassis of the vehicle through a fixed bracket. The stator is the stationary part of a motor. The stator consists of three parts: stator core, stator winding and frame.
The action of the stator is to produce an alternating current and the action of the rotor is to create a rotating magnetic field.

The diameter of this TERCA Two-in-one retarder flange is 180mm, there are 4 holes, the flange screws are M16, and the drive shaft screws are M16.
Investing in our retarder flanges is a cost-effective solution to improve braking performance. By reducing wear and tear on standard brake systems, our flanges can extend their lifespan and minimize maintenance costs, ultimately saving you time and money.

The manual switch is divided into 5 gears, 0 means the retarder is closed, 1 means the retarder constant speed gear, 2 means 1/4 of the maximum retarding torque, 3 means 1/2 of the maximum retarding torque , 4th gear represents 3/4 of the maximum retarding torque, and 5th gear represents the maximum retarding torque.
The retarder handle switch is installed in the cockpit. The driver realizes the braking of the vehicle by selecting the appropriate gear. Typically mounted on the dashboard or under the steering wheel, it will provide one neutral gear and four to six control gears.

DHB-15A stator coil assembly is suitable for CAMA DHB series eddy current retarder. CAMA DHB series eddy current retarder suitable for long-distance and tourist buses with rear gearboxes.
The stator has several groups of internal coils, which are the main working parts of retarder. It is connected with the chassis of the vehicle through a fixed bracket. The stator is the stationary part of a motor. The stator consists of three parts: stator core, stator winding and frame.
The action of the stator is to produce an alternating current and the action of the rotor is to create a rotating magnetic field.

The retarder handle switch is installed in the cockpit. The driver realizes the braking of the vehicle by selecting the appropriate gear. Typically mounted on the dashboard or under the steering wheel, it will provide one neutral gear and four to six control gears.
When the car is ignited, the retarder is in a standby state. When the car needs to be slowed down, the purpose of slowing down can be achieved by turning the handle of the manual switch to the required gear step by step. If you want to turn off the slowing down function, just use the handle Turn the control switch handle back to 0 gear.

The AX8 series is divided into AX83-00 and AX83-40 models. AX8 series bus brake eddy current retarder suitable for all kinds of vehicles with long drive shafts.

Product Introduction：
1. Lighter, smaller and better performance;
2. Uniquely designed rotor to enhance torque durability and reduce loss;
3. Optimized current design to reduce current loss;
4. More corrosion resistant;
5. Modular design, longer use time;
6. It is installed in the middle of the drive shaft and has wide applicability.

The control unit of an eddy current retarder is a vital component responsible for managing and regulating the operation of the retarder system. Eddy current retarders are braking systems commonly used in heavy-duty vehicles to provide efficient and reliable braking force.
The control unit acts as the central intelligence of the eddy current retarder system, interpreting sensor inputs, processing signals, and regulating the braking force to ensure smooth and efficient operation. Its functionality is crucial in providing effective braking performance, enhancing vehicle safety, and optimizing overall vehicle dynamics.

The diameter of this 043 flange is 182mm, the flange screw is M16, and the drive shaft screw is M16.
Flange body is provided with a through hole in the middle, through the hole around a plurality of bolt holes. The outer circumference wall of the flange is provided with a plurality of connecting holes, through the hole of the mouth is arranged around the step groove, the step groove is inlaid with a sealing ring. There are multiple heat dissipation holes on the plate surface of the flange, so that the flange volume is light and the heat dissipation efficiency is fast.

Relay is a kind of electric control device, is when the change of the input quantity to meet the specified requirements, in the electrical output circuit to make the controlled quantity of a predetermined step change of an electrical appliance. Relay has control system and controlled system, usually used in the automatic control circuit, in the circuit plays the role of automatic regulation, safety protection, conversion circuit and so on.
It is an electronic control device, which has a control system (also known as an input circuit) and a controlled system (also known as an output circuit), and is usually used in an automatic control circuit. It actually uses a smaller current to control a larger current A kind of “automatic switch”.